# Soil Stabilization Contractors in St. Louis | Kuesel

> Lime and cement soil stabilization for St. Louis building pads, roads and parking lots. Kuesel stabilizes wet or soft subgrade so site work stays on schedule.

Canonical: https://kueselinc.com/services/soil-stabilization
Last updated: 2026-11-16

Lime and cement stabilization, full-depth reclamation, and subgrade improvement for asphalt contractors and site work in St. Louis.

Soil stabilization is mixing lime or cement into weak, wet or soft soil where it sits, turning it into a firm, workable base for building pads, roads and parking lots. It is the alternative to digging that soil out and trucking in replacement fill, with the stabilizer, rate and depth set by the project's geotechnical mix design. Kuesel is one of the soil stabilization contractors St. Louis GCs, developers and engineers rely on — family-owned in O'Fallon, MO since 1963, with in-house crews and owned equipment.

- Lime and cement treatment of poor subgrade in place
- Full depth reclamation of failed pavement
- Subgrade drying, asphalt pulverization and base stabilization
- In-house crews and owned equipment — often instead of undercut-and-replace

## Capabilities

- Lime stabilization
- Cement stabilization
- Full-depth reclamation (FDR)
- Subgrade drying
- Geogrid & geotextile install
- Proof rolling with the GC and the owner's testing agency

## Soil and ground stabilization services in St. Louis

As a soil stabilization company, Kuesel provides ground stabilization with lime and cement treatment, subgrade drying, base stabilization and [full depth reclamation](/services/full-depth-reclamation) of existing pavement. Our in-house crews use the methods specified by the geotechnical engineer and lab mix design for building pads, drives and parking lots. Our soil stabilization service is often one step in our wider [commercial site work](/services/commercial-site-work): the same company grades the pad as your [earthwork contractor](/services/earthwork) and installs the storm, sanitary and water lines as a [site utility contractor](/services/site-utilities).

## What a soil stabilization contractor should bring (and what Kuesel self-performs)

- Builds to the engineer's design
- Prices stabilization against an undercut alternate
- Coordinates proof rolls with the GC and the owner's testing agency
- In-house crews and owned equipment
- Union labor

| Kuesel self-performs | By others |
| --- | --- |
| Lime stabilization | QC testing by the owner's testing agency |
| Cement stabilization | — |
| Subgrade drying | — |
| Base stabilization | — |
| Asphalt pulverization | — |

Fly ash and cement-modified soil (CMS) are described on this page for reference only; Kuesel does not self-perform them.

## How the stabilizer is chosen

The Federal Highway Administration's [Geotechnical Aspects of Pavements manual (section 7.6)](https://www.fhwa.dot.gov/engineering/geotech/pubs/05037/07d.cfm) gives the usual starting point: lime is generally considered for clay soils with a plasticity index (PI) above about 10 to 12, and cement for lower-plasticity soils.

That rule of thumb is not a design. The stabilizer, application rate and depth come from laboratory mix design testing, as laid out in [FHWA's stabilization mix design appendix](https://www.fhwa.dot.gov/engineering/geotech/pubs/05037/af.cfm). The lab work is done for the project engineer or geotechnical engineer; Kuesel follows that mix design in the field. When the choice is between treating the soil and removing it, our guide to [lime vs cement vs undercut](https://kueselinc.com/guides/lime-vs-cement-vs-undercut) compares the options.

## Stabilization methods

### Lime stabilization (quicklime)

Lime is generally used on high-plasticity clay — the kind of soil common in the St. Louis area that turns soft and sticky when wet. In the short term it modifies the clay: it dries the soil, lowers the plasticity index and makes it easier to work and compact.

Over the longer term, lime reacts with the clay minerals in a pozzolanic reaction that adds strength. Specifications often call for a mellowing period between initial and final mixing so the lime can work through the clay before the layer is finished.

### Cement stabilization

Portland cement hydrates and binds the soil particles together. It is generally suited to low-plasticity, silty or granular soils, and it is commonly the agent used in full-depth reclamation of failed pavement.

Because cement starts to set once it is mixed with water, compaction must be completed within the working time allowed by the specification after mixing. That makes sequencing of spreading, mixing and compaction critical.

### Fly-ash stabilization

Class C fly ash is self-cementing and can stabilize soil on its own. Class F fly ash typically needs lime or cement as an activator. Availability varies by region, so the engineer's choice depends partly on what can be supplied for the project.

### Cement-modified soil (CMS)

Cement-modified soil uses a lower cement content to improve workability, cut the plasticity index and give the job a working platform. It differs from cement-stabilized subgrade or cement-treated base, which are designed to reach a strength target. Our guide on [cement-modified soil vs. cement-treated base](https://kueselinc.com/guides/cement-modified-soil-vs-cement-treated-base) covers the difference in more depth.

### Modification vs. stabilization

- Modification improves workability: the soil dries, its plasticity index drops and it can be graded and compacted. It is not counted on for a structural value.
- Stabilization is designed to reach a strength value — such as unconfined compressive strength, CBR or resilient modulus — that the engineer uses in the pavement or slab design.
- The same agent can do either. The design intent, application rate and testing decide which one the spec is asking for.

## When to use each

| Option | Soil type / PI | Primary goal | Typical use | Notes |
| --- | --- | --- | --- | --- |
| Lime | High-plasticity clays (higher PI) | Dry and modify the clay, then long-term strength gain | Building pads, pavement subgrade and wet clay that fails proof roll | Often specified with a mellowing period between initial and final mixing |
| Cement | Low-plasticity, silty or granular soils | Bind the soil into a stiffer, stronger layer | Pavement subgrade, base stabilization and FDR | Compaction must be completed within the spec's working time after mixing |
| Fly ash | Varies; set by the mix design | Self-cementing (Class C) or activated with lime or cement (Class F) | Where specified and locally available | Regional availability varies |
| Cement-modified soil (CMS) | Soils that need workability improvement | Working platform and lower plasticity, not a strength target | Construction platforms and subgrade that must be workable | Lower cement content than a strength-designed layer |
| Undercut and replace | Any soil the engineer rejects | Remove unsuitable soil and replace it with approved material | Deep soft zones, unsuitable fill, or where treatment is not specified | Needs haul-off, a disposal site and import material |

See the [lime vs. cement vs. undercut guide](https://kueselinc.com/guides/lime-vs-cement-vs-undercut) and the [stabilization vs. undercut tool](https://kueselinc.com/tools/stabilization-vs-undercut).

## Specs and geotechnical context

- The geotechnical engineer of record and the lab mix design govern the stabilizing agent, application rate and treatment depth. We build to that design.
- In Missouri, MoDOT's Standard Specifications for Highway Construction govern MoDOT work, and project specifications on other work often reference them.
- Typical verification includes field density and moisture testing, depth and pulverization checks, and proof rolling. Quality-control testing is performed by the testing agency retained by the owner, not by Kuesel.
- Sulfate-bearing soils can heave when treated with calcium-based stabilizers such as lime or cement, so sulfate testing should be considered when the specification calls for it.
- Weather limits apply: most specifications restrict work in freezing temperatures and high wind, and require the treated layer to be protected while it cures.

## Process

1. Geotech review and mix design
2. Scarify and pre-pulverize the subgrade
3. Spread the agent at the design rate, with dust control
4. Mix to depth with a reclaimer / stabilizer
5. Add water to the target moisture
6. Compact
7. Fine grade
8. Cure or seal
9. Test and proof roll before paving or slab

## Equipment

- Spreader trucks: Spread lime or cement across the subgrade at the rate set by the mix design.
- Reclaimer / mixer: Mixes the agent into the soil to the specified depth, and pulverizes pavement and base on FDR work.
- Compaction equipment: Compacts the treated layer after mixing and moisture conditioning.
- Grading equipment: Fine grades the treated subgrade to the elevations on the plans.
- Water trucks: Bring the mixed soil to the target moisture and help control dust.

## Who it's for

- [General contractors on hard-bid work](https://kueselinc.com/general-contractors) - Send the ITB, plans and geotech. We price stabilization to the spec, and undercut as an alternate when you want the comparison, then schedule proof rolls and testing around your paving or slab sub.
- [Owners and developers](https://kueselinc.com/developers) - When soft clay threatens a pad or parking lot budget, an early look at stabilization against undercut can keep material on site and the schedule intact.
- [Engineers](https://kueselinc.com/engineers) - We read stabilization specs from the field side and can give early budget pricing for stabilization vs. undercut while you design. The design decisions stay yours.

## Stabilization projects

### Featured project: Tire plant Phase II, Clarksville, TN

On Phase II, Kuesel lime-stabilized 327,817 SY under the building pad, pavements, rail spur and laydown yards using about 10,300 tons of lime, at three different depths and rates on a pad with deep equipment pits cut inside it. [See the Clarksville tire plant project](https://kueselinc.com/projects/clarksville-tire-plant)

### Stabilization projects on the record

| Project | Client type | Location | Agent | Area / depth | Outcome |
| --- | --- | --- | --- | --- | --- |
| [Tire Plant Phase II](https://kueselinc.com/projects/clarksville-tire-plant) | Industrial (tire plant) | Clarksville, TN | Lime, about 10,300 tons | 327,817 SY — building pad 16" at 5%; pavements and rail spur 12" at 4%; laydown yards 12" at 3% | Building pad lime-stabilized at three different depths and rates, with deep equipment pits cut inside the pad. |
| [Retail Pavement Cement Stabilization](https://kueselinc.com/projects/alton-retail-cement-stabilization) | National retail store | Alton, IL (Madison County) | Portland cement at 7% | About 4,300 SY at a 12-inch depth | Subgrade treated in place instead of undercut, so paving could follow. |
| [University Track & Soccer Upgrade](https://kueselinc.com/projects/columbia-athletics-soil-stabilization) | University athletics | Columbia, MO | Portland cement | Stabilized to a 12-inch depth | Soil stabilization subcontractor with union labor; compaction by others. |
| West Plains Baseball/Softball Field (2024) | School athletics field | West Plains, MO | Quicklime at 2.5% | 11,235 SY at a 12-inch depth | Quicklime subgrade stabilization, spread, mixed and watered by Kuesel. |
| University City, MO cement-stabilized base (2023) | Available on request | University City, MO | Portland cement at 4% | 1,148 SY at a 12-inch depth (existing aggregate base) | Existing aggregate base cement-stabilized in place, with the subgrade restored to ±0.10 ft. |

More stabilization project references are available on request.

## Guides

- [Lime vs. Cement vs. Undercut](https://kueselinc.com/guides/lime-vs-cement-vs-undercut) - Plain-English comparison of subgrade fixes in Missouri, with a checklist for engineers.
- [Stabilizing Building Pads and Paving Subgrade on St. Louis Clay](https://kueselinc.com/guides/stabilizing-building-pads-and-paving-subgrade-st-louis-clay) - Why local clays and loess fail, how pad and pavement goals differ, and a checklist for GCs and developers.
- [Soil Stabilization Cost Factors](https://kueselinc.com/guides/soil-stabilization-cost-factors) - The qualitative drivers behind a stabilization price and how to compare it fairly with undercut.
- [Cement-Modified Soil vs. Cement-Treated Base](https://kueselinc.com/guides/cement-modified-soil-vs-cement-treated-base) - How cement-modified soil and cement-treated base differ in purpose, design and testing.

## Soil stabilization FAQs

### What is soil stabilization?

Soil stabilization is mixing lime or cement into weak, wet or soft soil where it sits, so it becomes a firm, workable base for a building pad, road or parking lot instead of being dug out and replaced. A soil stabilization contractor spreads and mixes the stabilizer to the agent, rate and depth set by the geotechnical engineer's mix design, then compacts and grades it so paving or a slab can follow. Kuesel, a family-owned St. Louis site contractor in O'Fallon, MO since 1963, self-performs lime and cement stabilization, subgrade drying and base stabilization with in-house crews and owned equipment. Quality-control testing is done by the owner's testing agency.

### Lime vs. cement: which does my site need?

As a general guide, the Federal Highway Administration's [Geotechnical Aspects of Pavements manual (section 7.6)](https://www.fhwa.dot.gov/engineering/geotech/pubs/05037/07d.cfm) says lime should be considered for clay soils with a plasticity index above about 10 to 12, while cement is more commonly used on lower-plasticity soils. The final choice, application rate and depth come from laboratory mix design testing, described in [FHWA's mix design appendix](https://www.fhwa.dot.gov/engineering/geotech/pubs/05037/af.cfm). We follow the project engineer's or geotechnical engineer's mix design; we do not run the lab.

### What affects the cost of soil stabilization?

The main factors are the area to be treated, the treatment depth, the stabilizer type and application rate set by the mix design, how wet the soil is, site access, and the testing the specification requires. We price each job from the plans, geotech report and mix design, and can price an undercut alternate alongside it. Our guide to [soil stabilization cost factors](https://kueselinc.com/guides/soil-stabilization-cost-factors) covers each one.

### Can you stabilize soil in cold or wet weather?

Wet soil is one of the most common reasons to stabilize: lime and cement dry out soft, wet subgrade so grading and paving can continue instead of waiting for it to dry on its own. Cold weather is different. FHWA's [Soil and Base Stabilization manual (Volume II, mixture design)](https://www.fhwa.dot.gov/pavement/pubs/014732.pdf) advises that lime-cement stabilization should not be attempted when the soil temperature is below 40°F. Most specifications also restrict work in high wind and require the treated layer to be protected while it cures.

### Stabilize or undercut?

Where the engineer approves it, stabilizing soil in place avoids hauling soft soil off site and importing replacement fill, which cuts trucking and spoils. Undercut can still be the right call for deep soft zones or unsuitable fill. We price both so GCs and developers can compare them; our [lime vs. cement vs. undercut guide](https://kueselinc.com/guides/lime-vs-cement-vs-undercut) walks through the trade-offs, and the [stabilization vs. undercut tool](https://kueselinc.com/tools/stabilization-vs-undercut) compares cost, schedule and trucks for a specific site.

### What about dust?

Kuesel spreads lime and cement dust-free from its own state-of-the-art spreader trucks. We also follow the specification's wind limits, use water trucks, and mix the agent in promptly after it is spread. Occupied or sensitive sites get a spreading plan agreed with the GC in advance.

Request a bid: [send the ITB, plans and geotech](https://kueselinc.com/bid-invite). Negotiated or design-assist project? [Talk to us early](https://kueselinc.com/work-with-owners).

## Projects

- [Tire Plant Sitework](https://kueselinc.com/projects/clarksville-tire-plant)
- [Equipment Yard Site Development](https://kueselinc.com/projects/berkeley-equipment-yard-site-development)
- [Retail Cement Stabilization](https://kueselinc.com/projects/alton-retail-cement-stabilization)
- [Food Plant Addition Site Work](https://kueselinc.com/projects/st-peters-food-plant-building-addition)
- [University Track & Soccer Upgrade](https://kueselinc.com/projects/columbia-athletics-soil-stabilization)

## Cities we serve

- [Soil Stabilization in St. Louis, MO](https://kueselinc.com/services/soil-stabilization/st-louis-mo)
- [Soil Stabilization in O'Fallon, MO](https://kueselinc.com/services/soil-stabilization/ofallon-mo)
- [Soil Stabilization in St. Charles, MO](https://kueselinc.com/services/soil-stabilization/st-charles-mo)
- [Soil Stabilization in St. Peters, MO](https://kueselinc.com/services/soil-stabilization/st-peters-mo)
- [Soil Stabilization in Chesterfield, MO](https://kueselinc.com/services/soil-stabilization/chesterfield-mo)
- [Soil Stabilization in Wentzville, MO](https://kueselinc.com/services/soil-stabilization/wentzville-mo)
- [Soil Stabilization in Belleville, IL](https://kueselinc.com/services/soil-stabilization/belleville-il)
- [Soil Stabilization in Maryland Heights, MO](https://kueselinc.com/services/soil-stabilization/maryland-heights-mo)
- [Soil Stabilization in Granite City, IL](https://kueselinc.com/services/soil-stabilization/granite-city-il)
- [Soil Stabilization in Edwardsville, IL](https://kueselinc.com/services/soil-stabilization/edwardsville-il)
- [Soil Stabilization in Hazelwood, MO](https://kueselinc.com/services/soil-stabilization/hazelwood-mo)
- [Soil Stabilization in Collinsville, IL](https://kueselinc.com/services/soil-stabilization/collinsville-il)

## Contact

|  |  |
| --- | --- |
| Phone | (636) 978-3478 |
| Address | 854 Lone Star Drive, O'Fallon, MO 63366 |
| Office hours | Monday–Friday 7:00 AM–4:00 PM |
| Service area | the St. Louis region |
| Bids | We confirm whether we're bidding within 1 business day. |

## Related

- [All services](https://kueselinc.com/services)
- [Request a bid](https://kueselinc.com/contact)
- [Request a bid](https://kueselinc.com/bid-invite)
- [Services](https://kueselinc.com/services)
- [Projects](https://kueselinc.com/projects)
